Tools

Truing stand upright extensions install in seconds on any TS-2 or TS-2.2 Truing Stand, allowing the stand to be used on wheels with hubs up to 200mm wide (tandem, fat and downhill bikes), as well as on wheels with a 29-inch mountain bike tire installed*. In addition, specially sized bosses serve as adaptors so the stand can be used with wheels using thru-axle hubs with removable axles. Same features as the the TS-2EXT.2 with the addition of slots to secure rear drive e-bike wheels. * Note: TS-2.2 Truing Stand does not require these adaptors to accommodate 29-inch wheels but does require it to fit hub widths from 180mm to 200+mm.

Park's Tire Seating Tool is designed to quickly seat the bead on stubborn tires. During inflation some tire beads can slip below the rim edge and become difficult to pull out and align. The PTS-1 comes to the rescue with its non-slip jaws and vinyl-coated handles that provide plenty of leverage for pulling out the tire. Plus, it's adjustable to fit various tire widths.

Park Tool's Bottom Bracket Bearing Tool Set removes and installs (with a bearing press which is sold separately) BB86, BB90, BB92 and Press Fit bottom brackets from Shimano, Race Face, SRAM and others that use a nominal 24mm-diameter spindle. This tool has a bearing remover that fits inside the bottom bracket shell and into the bearing so the bearings can be tapped out of the frame with a hammer. The set also includes two bushings that you use in conjunction with a bearing press for precision bearing installation (bearing press sold separately).

The HBH-3 securely holds handlebars in place on any bike in any position while in a repair stand. It's useful for brake bleeding, cable and housing routing, lever adjustment, or any scenario where you want to prevent the handlebars from rotating, including storage or working with the bike rotated upwards. With its articulating clamps and adjustable straps, the HBH-3 can easily be attached in a wide variety of positions onto almost any handlebar, seatpost, frame, fork, or repair stand. Anodized aluminum construction with soft rubber straps. - Straps install onto any round tube from 12mm to 60mm (0.5" to 2.4"), as well as most irregular and aero-shaped tubing found on bicycles - Rotating articulating clamps allow for secure installation onto virtually any bicycle in a wide range of positions - Usable extension length of 18" to 32" (45cm to 81cm) - Collapses and folds to 17" (43cm) for storage

After pressing the special connecting rivet into a Campagnolo 11-Speed Chain and breaking off the pilot, Campagnolo requires the end of the connecting rivet to be "peened" or "deformed" to prevent chain failure. The precision-machined CT-11 is used to accurately perform this critical process. Note: The CT-11 will not install or remove chain rivets. Its sole function is to peen and secure the end of the Campagnolo 11-speed connecting rivet. The Park Tool CT-4.2 Master Chain Tool (or previous model CT-4, each sold separately) is used for rivet installation and removal.

• Secure engagement, easy to use, and fast! • The CP-1 quickly grips cogs from 9 to 24 teeth with no manual adjustments • A great shop tool, the CP-1 is 13.7" (35cm) long and can be used with one hand to hold cassettes solidly during lock ring removal • Forged steel construction with a spring loaded return and comfortable dual density grips.

Secure engagement, easy to use, and fast! The CP-1.2 quickly grips cogs from 9 to 24 teeth with no manual adjustments. A great shop tool, the CP-1.2 is 13.7-inches (35cm) long and can be used with one hand to hold any 5-speed to 12-speed road or mountain cassette solidly during lock ring removal. Forged steel construction with a spring loaded return and comfortable dual density grips.

Park's Freewheel Remover Wrench provides superior leverage for freewheel removal and installation. Its head slides over Park freewheel removers and features a locking knob for a secure fit.

This professional-grade set includes five unique cleaning tools purpose-built for scrubbing away dirt and grime, with long ergonomic handles for leverage and comfort. The soaping brush, bottle brush and straight brush feature bristles made from tampico, a natural fiber derived from the agave plant. Tampico is extremely durable, resists chemicals, and holds moisture well, making it an ideal material for cleaning brushes. BCB-5 FEATURES Included brushes: - Soaping Brush: Great for making an initial pass over the bike, dispersing soapy water and breaking up large accumulations of debris. - Tapered Bottle Brush: A general purpose tampico brush for scrubbing areas both big and small. - Straight Brush: A long-reach brush with short, tight tampico bristles for getting into small nooks and crannies such as suspension pivots, saddle rails, and other hard to reach areas. - Drivetrain Brush: Long, stiff nylon bristles make this brush ideal for derailleurs, cassettes, and other areas with grease or dirt build up. - Soaping Sponge: Useful for applying soap and water as well as cleaning delicate surfaces, with a convenient wedge shape. Notes about tampico fibers: - Tampico is a natural fiber: as such, variations in the color of the bristles are to be expected. - Tampico bristles may become temporarily deformed in shipment or storage. Get brushes wet, reshape by hand, and hang to dry. - Always allow tampico brushes to dry fully in an open area before storage to inhibit growth of mildew or mold.

A great shop accessory made to hold a wide variety of axles, spindles and any Park Tool Freewheel Remover/Lockring Tool. Made from precision extruded aluminum.

Park's Oversize Adjustable Saw Guide guides a hacksaw so that you can accurately cut fork steerers, airfoil-shaped seatposts and more. The guide is made to be held in a vise and it has hardened-steel cutting slots and a secure clamp for the part you're cutting so that you make a perfect cut every time. The guide is compatible with round tubes from 1 to 1-3/4 inches in diameter and airfoil shaped parts up to 3.5 inches long. There are slots for standard and carbon-specific saw blades.

An economical option for safely and accurately tightening fasteners to proper torque specifications. With a simple gauge readout, the TW-2.2 is intuitive and easy to use, and applies up to 60 Nm of torque to any fastener or component with left or right-handed threads. Perfect for mid-to-high-torque applications such as bottom brackets, cassette lockrings, and crank bolts. 3/8" drive for compatibility with all Park Tool sockets, bits, and crow feet, as well as most threaded bottom bracket tools. - 0 to 60 Newton meter (0 to 50 foot-pound) range - 3/8" drive - Reads and registers torque values for both left hand and right hand threading - Length: 17.75" (450 mm)

- Brake holder features M5, M6 & passthrough holes for attaching all disc brake mounting styles as well as most rim brake caliper styles - 1-1/8" steerer tube features star nut for retaining top cap and spacers - 2" flared cone for compatibility with tapered steerer tubes - Compatible with 1-1/8" threadless stems only—not compatible with threaded headset/quill stem setups

A dirty drivetrain causes poor shifting and unnecessary wear to expensive parts. The Chain Gang contains everything needed to quickly and easily clean the chain, freewheel cogs, and chainrings. The Chain Gang includes: - CM-5.3 Cyclone Chain Scrubber - GSC-1 GearClean Brush - 8 oz. bottle of Bio ChainBrite The CG-2.4 works on nearly any bike, including multi-speed, single-speed, and e-bikes.

Park Tool's FR-5H is a fast and convenient tool to remove and install 12-spline Shimano/SRAM-style cassette lockrings, as well as similar lockrings on rotor discs. The FR-5H features a modified FR-5 tool that allows use without removing most quick release skewer nuts. The removable, threaded steel handle makes it possible to replace a worn or damaged head.

Precision CNC machined dual-sided aluminum tool for the installation and removal of 12- and 36-notch external bearing bottom brackets. Anodized for easy identification and featuring a ratchet/torque wrench compatible 3/8-inch drive. Fits Praxis M30 and M35 - M30: 12-notch 48mm OD cup - M35: 36-notch 51.7mm OD cup

Bottom brackets have some of the highest torque specs of any component found on a bicycle. Despite this, some bottom bracket cups feature tool fittings that allow mere millimeters of engagement, which can be a problem when attempting removal or installation. Solution: the Park Tool Bottom Bracket Tool Retaining System. Used in conjunction with nearly any Park Tool bottom bracket tool, the BBT-RS uses a spring-based tension system to apply consistent, adjustable pressure to the tool, ensuring full engagement with the tool fitting and preventing slippage. The BBT-RS can be configured for use with the vast majority of threaded and thread-together bottom bracket standards. The BBT-RS features an M8 threaded rod and a double-sided adapter nut with M12 and M15 threads, allowing it to thread directly into any compatible cartridge bottom bracket. The M15 adapter can also be used to install any of Park Tool's nine aluminum bottom bracket tools, all of which feature integrated threading for use with the BBT-RS. - Washer diameter: 57 mm (2.25") - Rod length: 175 mm (6.9") - Rod threading: M8 x 1.0 - Adapter nut threading: M12 x 1.0 & M15 x 1.0 Compatible with the following bottom bracket styles: - Threaded cup - Thread-together - Cartridge - Cup-and-cone Compatible with the following bottom bracket tools: - The following Park Tool socket-style aluminum bottom bracket tools: - BBT-27.3 - BBT-35-12 - BBT-35-36 - BBT-47-12 - BBT-47-16 - BBT-49.3 - BBT-59.3 - BBT-69.3 - BBT-79.3 - Wrench-style bottom bracket tools with a handle (e.g. Park Tool BBT-9, BBT-29, HCW-4) - Bottom bracket tools with external wrench flats (e.g. Park Tool BBT-19.2, BBT-22)

An economical option for safely and accurately tightening fasteners to proper torque specifications. With a simple gauge readout, the TW-1.2 is intuitive and easy to use, and applies up to 14 Nm of torque to any fastener or component with left or right-handed threads. Perfect for low-torque applications such as stem bolts, levers, and carbon fiber components. 3/8" drive for compatibility with all Park Tool sockets, bits, and crow feet. - 0 to 14 Newton meter (0 to 140 inch-pound) range - 3/8" drive - Reads and registers torque values for both left hand and right hand threading - Length: 11.5" (292 mm)

The RT-2 Head Cup Remover makes headset cup removal easy. The tool is pulled through the frame until the flared ends snap in behind the cup. A blow on the tool head removes the cup. • Designed for the 1-1/4 inch and 1-1/2 inch headest standards • Also easily removes cups on one-piece cranks • Strong, heat-treated alloy steel with a nickel finish SHIS Terminology: The RT-2 will remove cups of ZS44, ZS49, ZS55, ZS56, EC49 and EC56 headsets.

Park's Bottom Bracket Bearing Tool Set removes and installs (with a bearing press, which is sold separately) BB30, PF30, EVO 386 and BBright bottom bracket bearings. This fine tool slides through the bottom bracket shell and into the bearings so the bearings can be tapped out with a hammer. Two bushings for installing BB30 and PF30 bearings from SRAM and FSA are included (press required and sold separately).

Park's Professional Pedal Wrench features an angled, oversize head for maximum leverage. It has two 15mm wrenches at different angles, so you can maximize your leverage, and a long, round, vinyl-coated handle that won’t dig into your hand the way flat wrenches do. There's even a hole in the end for hanging the wrench on your toolboard.

Say goodbye to jumbled drawers and crowded bit holders. The JH-3 keeps your bits, sockets, and other tools well-organized and within reach, with three rows of moveable bit holders to fit up to 45 tools with 3/8" drive fittings. Precision-cut openings along the back allow for convenient storage of torque wrenches, drivers, and ratchets. Integrated mounting holes allow for straightforward installation on pegboard or any solid surface. - Assembled dimensions: 14" x 5.8" x 6.2" (356 x 148 x 158 mm) - Mounting holes are 10" (25.4 mm) from center to center - Mounting hardware not included - Durable powder-coated steel construction

A puncture in your tubeless tire doesn't have to be a death sentence for your ride. This handy carry-along tool repairs small punctures and cuts in tubeless bicycle tires without removing the tire from the rim, getting you back on the trail in no time. The TPT-1 easily plugs the hole by inserting one of the 5 included vulcanized rubber plugs into the puncture. This shrinks the puncture down to a manageable size, allowing the tubeless sealant to do its job and reestablish a seal. The unique sliding plug retainer holds the plug in place and prevents it from being pulled back out as the tool is removed. Everything is stored in a compact package that fits easily in a saddlebag or backpack pocket. - Includes 5 vulcanized rubber plugs (refills available — part #2370K) - Dimensions: 89 x 27 x 40 mm (3.5" x 1.1" x 1.6") - Weight: 79 grams (2.8 oz.) with plugs NOTE: Intended for tubeless bicycle tires using sealant only. Not compatible with inner tube systems.

Professional quality component hex driver precisely machined to exact standards to ensure a perfect fit on compatible component fasteners. Featuring an ergonomic, CNC machined, perfectly balanced 6061 aluminum handle hard anodized to take the rigors of everyday use.

Updated to fit current 12-speed cassettes, this combination chain whip and freewheel / lockring remover wrench is heat treated to prevent bending, flexing and wear and features a long, molded handle in addition to a built in hex shaped driver. - Works on 5- to 12-speed road and mountain bike cassettes and freewheels - 1-inch (25.4mm) box-end wrench fits Park Tool Freewheel / Cassette Lockring Tools - Features hardened pins to keep the chain in place

Precision component screwdriver machined to exact standards to ensure a perfect fit on compatible component fasteners. Featuring an ergonomic, CNC machined and hard anodized 6061 aluminum handle.

The MTB-5 packs 16 functions into one slim, tough folding multi-tool, making it the ideal companion for any trailside adjustment or emergency fix. Features a full set of hex wrenches and screwdrivers, a T25 Torx-compatible driver, and five specialty tools to aid in common on-the-ride repairs. Includes the following: - 2, 2.5, 3, 4, 5, 6 & 8 mm hex wrenches - T25 Torx-compatible driver - Philips #2 cross tip & flat head screwdrivers - Chain tool (5 to 12 speed compatible)* - Spoke wrenches (equivalent to SW-0 and SW-2) - Presta valve core removal tool - Disc brake rotor truing tool - Disc brake pad spreader *The MTB-5 will not peen Campagnolo 11, 12 or 13 speed chain rivets - Dimensions: 3.1" x 1.8" x 0.8" (79 x 45 x 20 mm) - Weight: 6.9 oz. (195 g) - Replaceable chain tool pin (Part #985-1)

The HCW-16.3 is a combination 15mm pedal wrench and chain whip. Use for both pedal removal/installation and for cassette removal. Chain whip features improved compatibility with 5-speed to 12-speed mountain and road bike cassettes and freewheels. The HCW-16.3 is 10.75" long (27.3cm).

Park's I-Beam Mini Fold-Up Hex Wrench/Screwdriver/Torx Set with Chain Tool includes 1.5, 2, 2.5, 3, 4, 5, and 6mm Allen wrenches, a socket 8mm Allen, a regular screwdriver, a T25 Torx tool (for disc-rotor bolts), a tire lever, spoke wrenches and a chain tool. The I-Beam conveniently fits in pockets and packs, too.

Precisely machined for a perfect fit, the LRT-5 removes and installs the lockrings that retain direct-mount chainrings found on Fazua® Ride 60 e-bike drivetrains. Features a 3/8" drive fitting for compatibility with most ratchet handles and torque wrenches, as well as 36 mm wrench flats for use with an adjustable wrench or crow foot. Heat-treated and plated 4140 steel construction ensures durability and long life. Fits lockrings with a 41 mm outside diameter and 16 notches including Fazua® Ride 60 e-bike drivetrains.